In The Shop: Starter Ring Gear Replacement

Here is a common repair that is frequent in every Harley Davidson service department. Starter ring gear replacement.

This is the large gear that is on the outer edge of the clutch basket. When the start button is depressed, the starter shaft shoots out and spins while engaging with this large ring gear. This action turns the primary drive which turns the crank shaft of the motor allowing the motor to cycle & start.



Under normal operating conditions, a starter ring gear will last for many years or thousands of start ups. However, it is very common for riders to install cheap, weaker batteries or utilize a quality battery beyond its life time. When a weaker battery is used, it puts a lot of strain on the starting system of a Harley. This not only diminishes the life of the starter and the starter clutch, but it also allows for poor starter shaft to ring gear engagement. This poor engagement eventually wears away the surface area on the teeth of the gears. Teeth can even break off of the gears.

Another reason a starter ring gear will fail prematurely is when a failing starter clutch is not addressed. If you hear a “zing-zing” type of sound at start up, you have a bad starter clutch. Again, this condition makes for a poor engagement with the starter ring gear.

If you hear a grinding sound when trying to start your Harley, you will need to remove your outer primary cover and inspect your starter ring gear. There are a options when it comes to this repair. If the repair is to be addressed with OEM parts, a new clutch basket assembly will need to be purchased from HD. The ring gear is not sold separately. In fact, it is held onto the aluminum basket with large, bold, rivets.



Another option is to purchase an aftermarket repair kit/assembly. Rivera Primo and Compufire sell excellent kits for this repair. The kits include the small starter shaft gear and the large starter ring gear.

The factory rivets are drilled and punched out. Then, the holes are drilled a little bit larger for the new retaining hardware. The new ring gear can then be bolted, securely onto the OEM Harley clutch basket. The kits typically have gears with less teeth (larger teeth allowing for more surface contact) for an even better, more definitive engagement over stock.



Related Videos:
Harley Clutch Assembly Upgrade

More on Topic Videos:
Removing Harley Starter and Speed Sensor Location
Harley Davidson Transmission Removal
Chrome Inner Primary Removal Procedure – Removing Pinon Gear / Jackshaft to Remove Starter
How to Install a Starter on a Motorcycle
Harley Starter Clutch Replacement
Harley 5 Speed Transmission Project
Harley Starter Push Pull Test
Motorcycle Electrical Wiring and Circuits
Harley Starter Clutch Problems
Motorcycle Starter Problems & Testing Tips


Share tips, start a discussion or ask one of our experts or other students a question.

Make a comment:
500 characters remaining

6 Responses to “In The Shop: Starter Ring Gear Replacement”

  1. Jeffrey Bowers

    </strong>I've got a1986 heritage softail need to put starter on and inner primary and clutch basket this was all off when I got from my brother after he was killed.. so this is New to me..

  2. Christopher Scroggs

    I have a question. I have a 1992 883. I thought I had a bad starter so I pulled my primary cover and bumped the starter. Turns out that my starter was fine . But when I hit the start button the starter gear engages the finger gear but the ring gear just spins freely. Without turning the engine. What is wrong here? Please help.

  3. William Anderson

    That's exactly what happened with the bike I just bought so I replaced both had had an aftermarket Barnett basket so I just replaced the ring gear and opinion but when I was removing them I grabbed ahold of my clutch basket and tried to move it back-and-forth it moved very little but it moved a fellow rider told me it should have a little bit of play not sloppy but I can almost see the chain moving a little bit when I go right to left back-and-forth As hard as I can This worried me a little bit and I thought maybe the bearing behind the basket was badd my friend ensured me that it is not but I still have my doubts I wondered if you could give me some input

  4. RICKY

    <strong> 19076 Ticket What size sockets are required for a 02 FXDL

  5. Larry

    ring replacement on 2016 road guide standerd.

  6. Bennie Myers

    My 2008 Electra starts easy when cold, but takes three or four times and sometimes a puff of smoke comes from the carb.